HVAC Design and Analysis

Day One

Welcome and Student Introductions

Review of HVAC Fundamentals

• Abbreviations, units, and references
• The need for environmental controls
• Properties of moist air, sensible and latent heat, air handing units and distribution
• Hot water and steam heating, vapor compression refrigeration, chilled water system components

Duct Design and Fan Selection

Ductwork and Materials Specification

• Ductwork: steel and aluminum, fiberglass and fiberboard, flexible and fabric, ductwork plenums
• Ductwork specialties: turning vanes and fittings, dampers and access doors, grilles, registers and diffusers, screens, louvers and hoods, sound attenuators
• Layout and distribution: sizing methods, aspect ratio and fittings
• Static pressure calculations
• Sample problems: AHU example 2-1, exhaust workshop 2-2
• Fan selection: performance, selection procedure, options, room air distribution design

HVAC Equipment Selection

Motors, drives, and motor controls

• Motors: types and options, motor selection
• Drives
• Motor controls: disconnect switches, starters, Variable Frequency Drives
• Packaged equipment selection
  • Packaged equipment sizes / capacity ranges
  • Using packaged equipment catalogs and selection software
  • DX coil / condensing unit selection
• Coils
• Coil performance
• Air and fluid side equations
• Fluid properties
• Coil types, options, circuiting
  • Coil sizing and selection
• Other terminal equipment
  • Variable Refrigerant Flow (VRF) systems
  • Radiant heating and cooling
  • Radiant / convective heating devices
• Radiant heating / cooling systems design
  • Radiant panel performance
  • Design steps
  • Layout options
• Chilled beam design
  • Design steps
  • Primary flow example

Day Two

Pumps and Pipe Design 

Piping and Materials Specification

• Pipe and fittings
• Valves and pipe specialties
  • Balance valves
  • Control valves
  • Pressure control valves
  • Pressure relief valves
  • Makeup water valves
  • Glycol fill systems
  • Flow meters
  • Expansion tanks
• Layout and distribution
  • Pipe sizing
  • Parallel flows
  • Reverse return
  • Primary / Secondary layouts
• Head pressure calculations
• Sample problems
  • Hot water example 3-1
  • Chilled water workshop 3-2
• Hydronic pumps
  • Pump performance
    • Pump curves
    • Parallel operation
  • Pump selection
  • Pump types
  • Sizing hydronic specialties
    • Expansion tanks
    • Pressure relief valves
    • Make-up water valves
    • Control valves

Heating and Cooling Loads

• Introduction and energy
• Heat transfer in buildings
• Weather data and solar heat gain
• Internal heat components
• Infiltration and ventilation
• CLTD / SCL / CLF method
  • Example 11 on page 28.54

Load Calculations

• Work session – sample problems
  • CLTD / SCL / CLF method
  • ASHRAE tables
  • Spreadsheet data
    • Sandwich shop sample problem 7-1
    • Hotel room workshop 7-2 (homework)
  • Hourly Simulations
    • Using hourly load simulation software
    • Trane Trace 3D Plus
      • Features and options
      • Input process
      • Output reports

Energy Code Compliance Paths

• Overview of compliance paths
  • IECC prescriptive
  • IECC performance
  • ASHRAE 90.1
• Portions of the prescriptive energy code
  • Building envelope requirements
  • Simplified HVAC compliance
  • Prescriptive compliance
    • Fan power
    • Duct leakage
    • Lighting
  • Building performance simulation paths
    • Performance Cost Index
    • Building Performance Factor

Day Three

Computational Fluid Dynamics

• What is CFD?
• How do you do CFD?
• Turbulence
• Ventilation and CFD
  • Examples - Healthcare
  • Examples - Laboratories
• Outdoor CFD
• Wind tunnel testing vs. CFD

 Building Information Modeling

• Floor plans and sections
• Equipment schedules
• System layout and sizing
• Revit load calculations

 Design Tools & Processes

• Coordination
• Visualization
• Laser Scanning
• Facilities Management
• Generative Design

Registration Date/Time:
6/2/2026 7:30am Central Time

Event Dates/Times:

• 6/2/2026  8:00am - 5:00pm Central Time
• 6/3/2026  8:00am - 5:00pm Central Time
• 6/4/2026  8:00am - 4:00pm Central Time

• Program Director

  Mark Malkin

• Gene Nelson

  Gene Nelson, PE, has 44 years of HVAC design experience with a mechanical contractor and two engineering firms. He has completed over 40 major projects (over 8 million square feet) located in cities coast to coast in the United States and in the Middle East. Projects included commercial, industrial, healthcare, pharmaceutical, and research and development (R&D) facilities. Gene is a Life Member of the American Society of Heating, Refrigerating and Air Conditioning Engineers (ASHRAE) and was President of the Madison ASHRAE Chapter from 2007 to 2008. He has been awarded ASHRAE’s Energy and Technology Award twice at the regional and society levels (1981 and 1994). Gene received his BS degree in Mechanical Engineering from the University of Wisconsin–Madison, and is a registered Professional Engineer in the State of Wisconsin.

• Duncan Phillips

  Senior Technical Director

  Duncan Phillips, PhD, PE, is a Senior Consultant at RWDI and firm-wide Practice Area Leader for the technical teams using Computational Fluid Dynamics (CFD) to solve building design problems. His post-graduate work involved experimental methods to assess how building HVAC systems interact with people. As such, he approaches any numerical modeling with a healthy level of suspicion but an understanding of how powerful CFD can be. He has over 20 years of experience applying CFD to building air flow problems. He will present the segment on CFD modeling and stack effect in tall buildings. The CFD segment will cover the background of what CFD is so that participants understand the capabilities and limitations. This background will be a pragmatic discussion of how CFD works, not a discussion of the equations.

• Mark Malkin

  Program Director and Teaching Faculty

  Mark P. Malkin, PE, is a program director in the Office of Interdisciplinary Professional Programs in the College of Engineering at UW-Madison. He is a registered Professional Engineer with over 25 years of experience in university facilities project management and HVAC systems design. His course offerings include HVAC, plumbing and fire protection fundamentals, building code reviews, and design and operation of science labs, data centers, museums and libraries. Mark received his bachelor's in Mechanical Engineering from Cornell University, and his MS in Mechanical Engineering from UW–Madison.

• Sagar Rao

  Co-founder

  Sagar Rao is a Co-Founder of NeuMod Labs in Madison Wisconsin, with a background in building physics, data engineering, and software development. As a Building Performance Consultant, he has successfully delivered over 50 high performance buildings for a clientele that includes federal agencies, state authorities, prominent healthcare systems, renowned universities, financial institutions, and national laboratories. Sagar provides leadership to several ASHRAE, International Building Performance Simulation Association (IBPSA), and Illuminating Engineering Society (IES) committees.

• Brian Clark

  Registered Mechanical Engineer

  Brian Clark, PE, is a registered mechanical engineer at the National Renewable Energy Laboratory. His experience is extensive and includes HVAC design of health care, laboratories, clean rooms, manufacturing, office space, and indoor waterpark resorts to name a few. He now focuses on building energy security and resilience research. Brian received his BS degree in Mechanical Engineering from Milwaukee School of Engineering.

• Dave Meinzer

  Sr. Project Design Engineer

  David J. Meinzer, DES, is a Sr. Project Design Engineer in the Science/Technology and Healthcare department at Ring & DuChateau, LLP (Ring & Du) Madison office, focusing on Laboratory and Healthcare HVAC design. Dave is a registered Designer of Engineering Systems (in the state of Wisconsin) with over 24 years of experience in HVAC systems design, including coordinating and collaborating design concepts with clients, other disciplines, and contractors. He has been leading or co-leading the mechanical design of Lab research projects for the last eight years. Dave is fluent in Revit modeling (including revit BIM 360), load calculations, and systems design.

• Kyle Hansen

  Design Technology BIM Manager

  Kyle Hansen leads the BIM (Building Information Management) group in Affiliated Engineers, Inc.'s (AEI) Madison headquarters. Since joining the firm in 2004, Kyle has been instrumental in expanding the technical capabilities of the BIM software suite and related design technologies. He has been the BIM Lead for many of AEI's most prominent large-scale, technically complex projects involving coordination of extended multi-firm project delivery teams, primarily in the national healthcare and research markets. Kyle's firsts for AEI include: first use of Revit Server model sharing and the implementation of owner/contractor asset tracking for the UWHealth's The American Center facility, first use of the subsequent BIM 360 simultaneous design platform, and first use of virtual reality for the Caltech Tianqiao & Chrissy Chen Institute for Neuroscience. He is a member of the National BIM Standards Committee. 

If you are planning to attend an Interdisciplinary Professional Programs course, payment is required at the time of registration. Below are the payment options:

Pay by Credit Card

Enroll online and pay by credit card.

• Search for the course on the website and then click on the Enroll Now button from the course webpage.
• Enter all necessary course attendee information and payment information on the course enrollment page.
• You will receive an email to confirm successful enrollment and payment.

Enroll over the phone and pay by credit card.

• Call CERC Registrations at 608-262-2451.
• Provide the registrations representative with:
  • the course name, dates, and/or course number.
  • the necessary course attendee information and payment information.
• You will receive either a mailed document or an email to confirm successful enrollment payment.

Pay by Check

Mail in a completed registration form and check payable to UW Madison.

• Fill out a registration form (found either in the back of the course brochure you received in the mail or here).
• Prepare a check, made payable to UW Madison.
• Mail the registration form and check to: CERC Registrations 21 N Park St, Ste 7101 Madison, WI 53715
• You will receive either a mailed document or an email to confirm successful enrollment and payment.

Pay by Purchase Order

• Request Purchase Order information from interpro@union.wisc.edu
  • If a fee quote is needed, contact custserv@interpro.wisc.edu first
• You will receive an invoice from UW–Madison Business Services for payment, usually within 3–5 business days

Military

If using SF-182 form, please call our registration number at 608-262-2451 or email interpro@union.wisc.edu for details and instructions.

Event Cancellation

We reserve the right to cancel a course due to insufficient enrollment or unforeseen events. If we cancel a course, participants will be notified via email or phone and will be given the option for a full refund or to transfer their registration and any fees paid to another course. We are not responsible for non-refundable plane tickets, hotel reservations, and other travel related expenses. For enrollee Course Cancellation, refer to notes on course page.

If you cannot attend, please notify us no later than one week before your course begins, and we will refund your fee. Cancellations received after this date and no-shows are subject to a $150 administrative fee. You may enroll a substitute at any time before the course starts.